Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above floor and clear of any moving door parts. Press PGRM key one time (LED will blink twice and go out indicating a new PIN is set). Press PRGM key one time (LED will turn solid indicating keypad is ready for new PIN). If the main PIN needs changed, follow these steps To cancel the temporary PIN, operate the keypad/door with the original main PIN.Press PGRM key one time (LED will blink twice and go out indicating a temporary PIN is set).Press PRGM key three times (LED will turn solid indicating keypad is ready for temporary PIN).This PIN will remain active until the main PIN is used again. If the keypad is to be used by normally unauthorized personnel (such as a repairman) a temporary PIN can be assigned to that personnel to gain access to the garage. Press number key corresponding with desired door (1, 2, or 3).STEP 4 - USING THE KEYPAD TO OPERATE OPENERS Continue with the remaining numbered steps. With blue LED still flashing, return to #3 in the section above and enter its opener ID# from CHART A. With keypad backlighting off, press the PROGRAM button 2 times to program a second opener OR press it 3 times to program a third opener (blue LED flashes slowly). Be ready to reference Chart A and then #3 from above: To program Opener #2 or #3 at any time, follow the steps below. MULTIPLE OPENERS: Complete steps for Opener #1 above. TIP: As soon as the opener activates, DO NOT press any additional buttons until the opener stops running. On the keypad, press the UP/DOWN key once every two seconds until the opener operates again. With the keypad LEDs still flashing, press the LEARN/PROGRAM button on the opener again for 2-3 seconds and then release.Ĩ. If you do NOT have one of these openers, programming of Opener #1 is complete.ħ. ONLY IF YOU HAVE A Chamberlain®/LiftMaster®/Craftsman® opener with a YELLOW LEARN button, please complete #7 & #8 below. All other listed names and trademarks are the property of their respective owners. Genie® and Intellicode® are registered trademarks of The Genie Company. On the keypad, press the UP/DOWN key once every two seconds until the opener operates.On the opener, press the LEARN/PROGRAM button for 2-3 seconds and then release.On the keypad, press and release the UP/DOWN key (LED flashes rapidly).On the keypad, enter the ID# of the opener from Chart A.On the keypad, press and release the UP/DOWN key (LED flashes slowly).On the keypad, enter a personal PIN (3-8 digits).NOTE: Steps #7 & #8 required for Chamberlain®/LiftMaster®/Craftsman® unit YELLOW LEARN button ONLY To start over at any time, start at STEP 2 - CLEARING THE KEYPAD. You will need your opener ID# from Chart A for these steps. This keypad can be programmed to up to 3 individual garage door openers in any combination of manufacturer specifications. If the opener/receiver has dip switch technology, please move to the alternate instructions listed on our website at this time: STEP 3 - PROGRAMMING TO ONE OR MORE OPENERS The keypad is now ready to be programmed.(tone will sound) - then release (green LED will flash and go out). Press both the PROGRAM & UP/DOWN keys at the same time and hold for 5 seconds.Remove activation tab from inside battery compartment.Perform this task first before setting the PIN or at anytime the keypad needs to be reset to its factory default: In some cases, this button could also be on an external receiver that is mounted on or nearby the product. For commercial openers, this button may be on the circuit board or the opener. For garage door openers, be sure to check under the light covers. Find the LEARN/PROGRAM button on the device - shape, color or name of this button could vary by brand.Locate the brand and opener/receiver specifications for the device by consulting the label on the opener/receiver, the instructions manual, the current remote controls for the opener, or the original manufacturer or the opener/receiver.STEP 1 - FIND SPECIFICATIONS & LEARN/PROGRAM BUTTON Do not press the LEARN button for longer than the noted 2-3 seconds as it could cause the operational remotes to no longer work.A temporary PIN can be set for convenient non user access.Keypad will operate up to 3 doors with one PIN number.An audible beep will sound with every key pressed.Genie Universal Keypad Compatibility Chart Genie Universal Wireless Garage Door Opener Keypad Programming Instructions
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |